Key takeaways
- A 90 amp sub panel suits a detached garage, workshop, or secondary structure that needs several circuits but not a full house load, while a smaller 60 amp…
A 90 amp sub panel suits a detached garage, workshop, or secondary structure that needs several circuits but not a full house load, while a smaller 60 amp panel fits light-duty needs like a shed with basic lighting and outlets, and a 100-125 amp panel suits a space with heavier equipment or future expansion plans. The right size depends on calculated load, not just how many breaker slots look convenient, and any sub panel installation should be verified against local electrical code and, in most jurisdictions, inspected by a licensed electrician.
A sub panel distributes power from a main panel (or another sub panel) to a specific area, carrying its own set of breakers while being fed by a single breaker or disconnect back at the source panel. The feeder breaker at the main panel and the wire gauge feeding the sub panel both need to be sized to match, or stay below, the sub panel’s rating.
Why 90 Amps Specifically
90 amp sub panels sit in a middle tier: more capacity than a typical 60 amp panel used for minimal lighting-and-outlet circuits, but less than a 100 or 125 amp panel sized for a workshop with welding equipment, a kiln, or substantial future expansion. Sizing a sub panel starts with adding up the amperage of circuits it will actually carry, not just filling every breaker slot, since code calculations (and common sense) factor in that not everything runs at once.
A qualified electrician performs this load calculation using the National Electrical Code’s methods, factoring in continuous versus non-continuous loads, and that calculation determines whether 90 amps has enough headroom or whether a larger panel makes more sense for the specific structure.
Breaker Slots and Panel Configuration
Panels in this amperage range commonly come in configurations offering a range of breaker spaces, often in the 12-24 slot range depending on the maker and whether slots are single-pole or allow double-pole breakers for 240V circuits. More slots give flexibility for future circuits without needing a tandem breaker or panel upgrade later, which is worth weighing against the panel’s physical size and mounting space available.
Main lug only (MLO) panels, common for sub panels, have no main breaker built in, relying on the upstream breaker at the source panel (or a separate disconnect) to protect the feeder. Some sub panels do include a main breaker for a local disconnect, which some codes require depending on the distance between the main panel and the sub panel, or whether the sub panel is in a separate structure.
At a Glance: Sub Panel Capacity Tiers
| Tier | Best for | Key stated specs | Limits |
|---|---|---|---|
| 60 amp sub panel | Shed or small structure, lighting and basic outlets only | Maker-stated 8-12 breaker slots typical, lighter feeder wire gauge | Little room for added circuits or higher-draw tools later |
| 90 amp sub panel | Detached garage/workshop with multiple circuits and some power tools | Maker-stated 12-24 slots depending on model, MLO or main-breaker versions available | May still be tight for heavy equipment like welders or large compressors; confirm with load calc |
| 100-125 amp sub panel | Workshop with heavier equipment or planned future expansion | Maker-stated higher slot counts, larger bus rating | Requires larger feeder wire and a correspondingly sized breaker at the main panel |
Fit and Compatibility Notes
The feeder wire gauge running from the main panel to the sub panel must be sized for 90 amps per code tables (commonly a copper conductor in the range an electrician will specify based on run length and conduit fill), and voltage drop over longer runs can require upsizing the wire beyond the minimum code gauge. Confirm the main panel has an available breaker slot and enough remaining capacity, since adding a 90 amp sub panel load onto an already-loaded main panel can require a service upgrade.
If the sub panel feeds a detached structure, code in most areas requires either a 4-wire feeder (separate neutral and ground) or specific grounding electrode requirements at the detached structure itself, plus a local disconnect in many cases. These details vary by code cycle and local amendment, so this is squarely an electrician’s call, not a DIY judgment.
Pick This If…
| Scenario | Suggested direction |
|---|---|
| Shed with lights and a couple outlets only | 60 amp sub panel is likely sufficient; confirm with a load calc |
| Detached garage/workshop, multiple circuits, light power tools | 90 amp sub panel, sized by an electrician’s load calculation |
| Workshop with welder, kiln, large compressor, or planned expansion | 100-125 amp sub panel with appropriately sized feeder |
| Main panel already near capacity | Have an electrician assess main panel capacity before adding any sub panel |
A Few Alternatives Worth Considering
For structures with modest, well-defined loads, a 60 amp sub panel is a lower-cost alternative that still covers lighting, standard outlets, and light-duty tools, provided the load calculation supports it. On the other end, a 125 amp sub panel gives more headroom for a workshop expecting to add equipment over time, trading a larger feeder wire and panel cost for that future flexibility. A third option some electricians discuss for larger detached structures is running a second full service rather than a sub panel, which makes sense mainly when the structure’s total demand approaches what a small home draws.
Installation and Safety Basics
Sub panel installation involves working inside live electrical panels and running feeder conductors, which carries real shock and fire risk if done incorrectly; this is work for a licensed electrician, and most jurisdictions require a permit and inspection regardless of who performs the labor. Never exceed the panel’s rated ampacity by adding more connected load than the panel and feeder were sized for, and label all breakers clearly once circuits are installed so future work or troubleshooting is safer.
If the sub panel will be in a damp location, such as an unheated garage or outbuilding, confirm the panel’s enclosure rating is appropriate for that environment, since standard indoor-rated enclosures are not meant for damp or wet exposure.
Breaker Compatibility and Future Expansion
Breakers installed in a sub panel generally need to match the panel maker’s approved breaker types, since panels are listed for use with specific breaker brands or classifications under safety certification. Mixing incompatible breaker brands into a panel not listed for them is a code violation and a real safety issue, even if the breaker physically appears to fit the slot. Buyers planning to add circuits gradually, rather than wiring everything at once, should ask their electrician whether the chosen panel’s open slots and bus rating leave enough headroom for that phased approach without exceeding the panel’s or feeder’s total capacity.
Tandem (twin) breakers, which fit two circuits into one slot, are an option some panels support for adding capacity without a larger panel, but not every panel or every slot within a panel is rated for tandem breakers. An electrician can confirm whether a specific sub panel model allows this and in which slots.
Permits, Inspections, and Why They Matter
Most jurisdictions require a permit for installing or upgrading a sub panel, and that permit process typically includes an inspection before the panel is energized for permanent use. Skipping this step isn’t just a legal risk; inspectors catch wiring and grounding issues that are hard for a non-electrician to self-identify, and uninspected electrical work can also complicate home insurance claims or future home sales if the work surfaces during a buyer’s inspection. Keeping the permit and inspection documentation on file is useful both for warranty purposes and for any future electrical work that builds on the sub panel’s circuits.
Frequently Asked Questions
How do I know if 90 amps is enough for my garage or workshop?
A licensed electrician performs a load calculation that adds up your actual and planned circuits, accounting for code-defined continuous and non-continuous load rules, to determine whether 90 amps leaves adequate headroom. Guessing based on breaker slot count alone can leave a structure undersized once real-world tool and appliance loads are added up.
Can I install a sub panel myself to save on labor cost?
Working inside an energized main panel and running a properly sized, code-compliant feeder is specialized work with real electrocution and fire risk, and most local codes require a licensed electrician and inspection for this kind of work. Attempting it without that qualification can also void insurance coverage if something goes wrong later.
Does a sub panel need its own ground rod?
If the sub panel feeds a separate detached structure, many code jurisdictions require a grounding electrode (such as a ground rod) at that structure in addition to the feeder’s ground conductor, though exact requirements vary by code cycle and local amendment. An electrician familiar with your local code can confirm what applies to your specific installation.
What size wire do I need to feed a 90 amp sub panel?
Wire gauge depends on the conductor material, the length of the run, and conduit fill, following the ampacity tables in the National Electrical Code; longer runs may need a larger gauge than the code minimum to control voltage drop. An electrician calculates this based on your specific run rather than a single generic answer.
Do I need a main breaker in the sub panel itself?
Some codes require a local disconnect at or near a sub panel feeding a separate structure, which can be satisfied by a main breaker in the sub panel or a separate disconnect switch nearby. Whether this applies depends on the distance between panels and local code requirements, which an electrician will confirm during planning.
Can I add more circuits to a 90 amp sub panel later?
If the panel has open breaker slots and the original load calculation left headroom under 90 amps, adding circuits later is often straightforward. If the panel is already near its calculated capacity, adding significant new load may require upgrading to a larger panel or feeder rather than simply adding another breaker.
You might also like
- Best Circuit Breaker Panel Lock: Picks and What to Look For (2026)
- Best 800 Amp Meter Base: Picks and What to Look For (2026)
- Best 200 Amp Breaker Box Outside: Picks and What to Look For (2026)
- Best Lattice Panels for Privacy: Picks and What to Look For (2026)
- Best 277V LED Retrofit Kits: Picks and What to Look For (2026)
- Best Variable Speed Squirrel Cage Fan: Picks and What to Look For (2026)