Updated Nov 18, 2026· 7 min read

Key takeaways

  • Builders converting a 22mm control panel opening to fit a 30mm pushbutton need a snap-in adapter bushing or knockout reducer, while anyone sealing an…

Builders converting a 22mm control panel opening to fit a 30mm pushbutton need a snap-in adapter bushing or knockout reducer, while anyone sealing an unused 30mm hole on an existing enclosure needs a blanking plug rated for the panel’s NEMA or IP environment; the right pick depends on whether the hole is being resized, adapted, or closed off entirely.

Why 30mm Matters on Control Panels

30mm is one of the two dominant industry standard mounting hole sizes for pushbuttons, pilot lights, and selector switches on industrial control panels, the other common size being 22mm. Major control component makers, including Allen-Bradley, Eaton, Idec, and Schneider Electric, all build pushbutton and pilot device lines around one of these two hole sizes, and panel builders frequently need to adapt between them when swapping an older 22mm device line for 30mm hardware, or vice versa, without re-cutting a new enclosure.

Because panel enclosures are often reused, replaced, or standardized across a facility, a knockout or adapter bushing is usually cheaper and faster than re-punching a new hole pattern, provided the existing hole and the new device’s mounting hardware are compatible with the adapter being used. Confirming both the existing hole size and the new device’s hole-size requirement before ordering an adapter avoids a mismatch.

Categories Worth Comparing

22mm-to-30mm adapter bushings

These snap or thread into an existing 22mm panel hole and provide a 30mm mounting surface on the front face, letting a 30mm pushbutton or pilot light mount into a panel originally punched for 22mm devices. They are the most common solution when upgrading or standardizing device sizes without reworking the enclosure.

30mm-to-22mm reducing bushings

The reverse case: a panel already punched for 30mm devices can accept a 22mm device using a reducing adapter. This comes up when replacing a larger legacy pushbutton with a newer, smaller-footprint device while keeping the existing panel cutout.

Blanking or knockout plugs

When a device is removed and the hole will not be reused, a snap-in blanking plug seals the 30mm opening to maintain the enclosure’s rated ingress protection. The plug’s own IP or NEMA rating should match or exceed the enclosure’s rating; a plug with no stated sealing rating is only appropriate for non-sealed or indoor general-purpose panels.

Factory pre-scored knockouts on new enclosures

Some enclosures ship with pre-scored, punch-out sections sized for 30mm devices built into the panel face, intended to be removed only when a device will actually be installed there. These are a feature of the enclosure itself rather than an aftermarket part, and once punched out, sealing an unused one later requires a separate blanking plug.

Type Best For Key Stated Specs Limits
22mm-to-30mm adapter bushing Mounting 30mm devices in an existing 22mm hole Snap-in or threaded, maker-stated panel thickness range Adds slight depth behind the panel face
30mm-to-22mm reducing bushing Mounting 22mm devices in an existing 30mm hole Snap-in or threaded, same panel thickness consideration Not interchangeable with 22-to-30 adapters
Blanking/knockout plug Sealing an unused 30mm hole Maker-stated IP/NEMA rating, snap-fit installation Rating varies by product; check against enclosure requirement
Factory pre-scored knockout New enclosures with planned future device locations Built into enclosure, punched out as needed Not a standalone purchasable part; a design feature of the enclosure

Fit and Compatibility Notes

Panel material thickness affects whether a given adapter or plug seats correctly; most snap-in adapters list a supported panel thickness range in the maker’s documentation, and using one outside that range can leave the adapter loose or unable to fully seat its retaining clips. Metal panels, especially thicker steel enclosures, sometimes need a threaded bushing rather than a snap-fit style for a secure, flush fit.

For sealed or washdown-rated enclosures, the blanking plug or adapter’s own ingress protection rating must be checked against the enclosure’s rating, since a panel rated for a wet or outdoor environment loses that protection at any opening sealed with a lower-rated plug. The maker’s specification sheet should state an IP or NEMA rating directly; if it does not, the component should be treated as a general indoor part only.

Device depth behind the panel is another detail worth checking before ordering, particularly in shallow enclosures, since stacking an adapter bushing behind a pushbutton’s own mounting collar adds depth that can interfere with wiring terminals or an adjacent device inside a tight enclosure.

Pick X If…

Pick If You…
22mm-to-30mm adapter bushing Are upgrading to 30mm devices in a panel originally punched for 22mm
30mm-to-22mm reducing bushing Are installing a smaller 22mm device into an existing 30mm cutout
Blanking/knockout plug Removed a device and need to reseal the hole, especially on a sealed enclosure
Factory pre-scored knockout Are specifying a new enclosure with planned, not-yet-installed device locations

Alternatives Worth Considering

For panels needing several size changes, a universal multi-size adapter plate that accepts several device sizes in one mounting frame can simplify inventory versus stocking individual bushings for every size combination. Where a hole will clearly never be reused, some panel builders prefer a welded or epoxy-filled patch over a snap-in plug for a fully flush, tamper-resistant finish, though this is more labor-intensive and generally reserved for permanent decommissioning rather than routine device changes. For brand-matched aesthetics, some device manufacturers sell their own branded adapter bushings designed to color- and finish-match their pushbutton and pilot light lines rather than using a generic third-party adapter.

Installation Notes

Snap-in adapters and plugs should be installed following the manufacturer’s stated panel thickness and hole tolerance, since an out-of-spec hole can prevent the retaining clips from seating fully, leaving the part loose or at risk of falling out under vibration. For control panels in regulated industrial environments, any changes to device mounting or enclosure openings should also be checked against the facility’s applicable panel-building standards and the enclosure manufacturer’s guidance for maintaining its rating.

Sourcing and Standardization Notes

Facilities that maintain many panels across different machine lines often benefit from standardizing on one device size, either 22mm or 30mm, across all new equipment specifications, which reduces the long-term need for adapter bushings altogether. Where standardization is not practical because of legacy equipment or mixed-vendor panels, keeping a small stock of both adapter directions and a few blanking plugs on hand avoids delays when a device is swapped or removed during maintenance. Panel-building documentation, including as-built drawings showing which holes use adapters versus native-size cutouts, is also worth keeping current, since a panel with several adapted holes can be confusing to service years later without a record of which bushing type is installed where.

Frequently Asked Questions

Can a 22mm-to-30mm adapter be reversed to go from 30mm to 22mm?

No; these are generally sold as separate, direction-specific parts because the geometry of the snap-fit or threaded retention differs depending on which hole size is the existing cutout and which is the target mounting size. Buyers should order the adapter matching their actual existing hole and target device size.

Do all 30mm blanking plugs provide a watertight seal?

No; sealing performance varies by product, and only plugs with a stated IP or NEMA rating from the manufacturer should be used on enclosures that need to maintain a sealed rating. A plug with no stated rating should be treated as suitable for general indoor use only.

Will an adapter bushing work on a thick steel enclosure panel?

It depends on the specific adapter’s stated panel thickness range; some snap-fit adapters are designed for thinner panels and will not seat correctly on heavier gauge steel, in which case a threaded bushing rated for the actual panel thickness is usually the better fit.

Does adding an adapter bushing affect the pushbutton’s electrical rating?

The adapter itself is a mechanical mounting part and does not change the electrical rating of the pushbutton or pilot device being installed; that rating comes from the device itself. The adapter’s only job is providing a correctly sized and, where applicable, sealed mounting interface.

Can a knockout plug be reused after being removed once?

Many snap-in plugs are designed for one secure installation, and repeated removal can wear down the retaining clips, reducing how securely they seat on reinstallation. For a location expected to be opened and closed repeatedly, a threaded plug rather than a one-time snap-fit style is generally a more durable choice.

What happens if the wrong size adapter is forced into a hole?

Forcing an incorrectly sized adapter can crack the panel material around the hole or damage the adapter’s retaining features, in either case compromising the fit and any sealing rating. Measuring the existing hole and confirming the adapter’s documented size range before installation avoids this.

M
Melu Editorial Team
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.